Saturday, May 24, 2014

Waterjetting 21c - collection in Gilsonite and steep seams

Picking up the debris from a waterjetting operation can be a more expensive part of the process than actually removing the material in the first place. This is particularly true where the material no longer has any inherent value, but is sufficiently toxic that it has to be collected and then properly disposed of. On the other hand, in most aspects of mining, it is the inherent value that is contained in that debris that makes the whole process worthwhile, and in this latter case requires that as much of the material be initially collected as possible. This can be difficult where, for example, gold particles are being produced, since these are heavy and naturally rapidly sink through the water to settle onto the floor where, if this is rough, they can then lie is natural traps that make it hard to re-elevate them and move them to a desired collector.

If one is to continue to move the particles there must be some mechanism that will continue to move the particles to the point that they can be collected. The very condition that makes it difficult to manually mine coal from steeply dipping beds also serves to carry coal and other minerals from those veins, once the material is broken free from the solid.

Consider, for example, the early mining of Gilsonite, which is a naturally occurring hydrocarbon found in thin vertical veins in places such as Utah. It is named after one of its first developers, Samuel H. Gilson.


Figure 1. Pieces of Gilsonite (Metroexpand )

The problem with mining this material is that the dust is very explosive, and remote, safer methods were needed to get men away from the mining process. In 1957 the major American company, American Gilsonite, turned to the use of hydraulic mining. At first the seam was mined using a series of horizontal lifts, with the washed out material and water being collected in drifts that carried it to a pumping station. However, because of the vertical seam, it was easier to used a drill, with lateral jets so that the rotating waterjets mined and flushed the material down into underlying drifts, where it could be collected.

Figure 2. Method for Mining Gilsonite.

By moving the mining tool along the vein the material could be mined out, without miners at the working face, and without the risks of explosion from the conventional mechanical mining methods.

A recent blimp trip over the Bonanza mine shows the results from years of the mining process, as the seam has been removed.


Figure 3. Mined out seam of Gilsonite at Bonanza, Utah. (J.S. and S.W. Aber)

More recently the mine has returned to a mechanical method for mining the material since the customer wanted a dry, rather than a wet product, and, with demand for the material rising, hopefully they will continue to operate safely – the material is now airlifted to the surface. Mining has been restricted to the top 500-ft of the vein.

The hydraulic mining process demonstrated here shows some of the advantages of the use of waterjets in that there are no workers in the mining area, and that the tool is able to remove the mineral without generating the sparks and explosive dust clouds that can be a danger otherwise.


Figure 4. German coal seam side view, showing thickness and angle of slope. (Benedum, W., Harzer, H., and Maurer, H., "The Development and Performance of two Hydromechanical Large Scale workings in the West German Coal Mining Industry," paper J2, Proc. 2nd Int. Symp. Jet Cutting Tech., BHRA.)

Coal mining has some of the same problems, and in Germany the idea was tried (in a slightly modified version) as a way of mining coal. Rather than operate from a drilling rig at the surface, holes were drilled along a very steeply dipping seam. The process was in two parts, evaluating whether it was better to start at the bottom and drill up, or to start at the top and drill down.

Figure 5. Methods tested for bore and mine coal recovery. (Benedum, W., Harzer, H., and Maurer, H., ibid.)

The method where the drill goes down, and then reams back up turns out to be the better approach. The reason for this is that the coal breaks out along natural planes, and these can produce coal pieces that are large enough to block the drilled hole through which all the material must pass, when drilling upwards. This is not a problem when drilling down, since the coal is falling through a much larger space (the mined out volume). This makes it a little more difficult to recover, since it is not confined where it falls into the lower drift. But, by adding a small monitor in the second drift, the broken coal can be lifted back into a slurry that can then be channeled into a flume, and carried away from the working area.

The process was effective, in that it showed that the coal could be mined from one drift to the next, using the method, but it was difficult, because of the varying conditions of the seam over its length, to make the connecting drill holes at an economic speed, and thus to mine the coal at an economic rate.


Figure 6. Looking down to the lower drift from the upper, after mining, with all the coal removed. (Benedum et al ibid)

Note that in the above picture there is little roof collapse into the mined out cavity. This is either beneficial (since it allows all the coal to be removed) or it can be a disadvantage. Other than the safety factor of having a roof hang up until a very large area collapses at one time (where the air blast can do considerable damage), a continual roof collapse as the coal is mined can provide confinement for the water and, hopefully, enough restriction that the water will carry the coal to a collection point.

This was the idea behind the JPL coal mining worm that they proposed some years ago:


Figure 7. The JPL concept for a horizontal jet mining system (Miller, C.G., and Stephens, J.B., Coal Worm: A Remote Coal Extraction Concept, JPL Report 5010-7, December, 22, 1976, Jet Propulsion Laboratory, Pasadena, CA.)

Unfortunately when a coal mine roof collapse occurs the rock breaks into relatively large pieces so that the water can flow away through the pile, without being confined sufficiently to provide the needed motive force to move the coal to the collection point. For that, the system would still need a steeply dipping bed, and I’ll talk more of this and debris collection in future posts.

No comments:

Post a Comment